Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Installation Cost in Upland?
Gate installation in Upland runs $2,400 to $9,500 for most residential projects in 2026, with the average automated driveway gate landing around $5,600 including the operator, safety devices, and haul-away of your old system. A basic manual swing gate on an existing footing sits at the low end near $2,400, while a wide dual-swing driveway with a LiftMaster or FAAC operator, keypad, and safety loops climbs toward $9,500 and beyond. The single biggest swing factor is whether a new footing and conduit run are needed; that alone can add $1,200 to $3,000.
We install gates across Upland every week, from the older ranch lots near Downtown Upland to the newer tracts off Foothill Boulevard and the equestrian properties that skirt the foothills. Below is a straight breakdown of what you’ll actually pay here, what moves the number, and how to keep the total down without cutting corners on the parts that keep people safe.
Gate Installation Cost Breakdown (2026)
These are real ranges for the Upland market, not national averages. Your actual quote depends on width, material, operator brand, and site conditions we can see in a free on-site estimate.
| Line Item | Typical Cost (Upland, 2026) |
|---|---|
| Manual single swing gate (materials + install) | $2,400 – $4,200 |
| Manual dual swing gate (driveway width) | $3,800 – $6,500 |
| Sliding gate (residential, up to 16 ft) | $4,500 – $8,000 |
| Automated swing operator (LiftMaster, FAAC, BFT) | $1,600 – $3,200 |
| Automated sliding operator (Viking, DoorKing, Elite) | $1,900 – $3,800 |
| New concrete footing / pad | $600 – $1,800 |
| Conduit run for power to the gate | $500 – $1,400 |
| Keypad or access control entry | $250 – $700 |
| Safety loops / photo-eye safety pair | $350 – $900 |
| Removal and haul-away of old gate | $200 – $550 |
The operator is where most of the spread lives. Entry-level residential brands like Ghost Controls and Mighty Mule keep a project lean, while professional-grade systems from FAAC, BFT, and DoorKing cost more up front and are built for heavier use and longer service life. We work with all nine major brands, so we’re not steering you toward whatever happens to be on the truck. We match the operator to your gate weight, your daily traffic, and how you want to open it.
If your existing gate is sound but the opener is dead, you may not need a full installation at all. Electric gate repair is often the smarter spend, and because we treat motor, control board, and access repair as primary work, we’ll tell you plainly when a repair beats a replacement. Repair or replace, we handle both.
What Affects Gate Installation Pricing in Upland
Two gates of the same width can land thousands apart. Here’s what actually moves the number in this market.
- Gate width and weight. A 12-foot single swing is a simpler job than a 20-foot dual swing or a long sliding gate. Heavier gates need stronger operators, thicker posts, and more concrete, and every one of those adds cost.
- Material choice. Wrought iron and steel cost more in materials and labor than aluminum or ornamental aluminum, but they hold up better against the dry heat and dust Upland sees through the summer. Vinyl sits at the low end but needs care in full-sun exposures.
- Site conditions and slope. Property around the foothills often slopes, and a gate on a grade needs different footing and closure work than a flat driveway. A sloped or uneven strike point can add $400 to $1,000 in fabrication and adjustment.
- Power availability. If there’s no convenient power at the gate line, we run conduit and pull a circuit. That’s the $500 to $1,400 line above, and it’s the item homeowners most often underestimate.
- Automation level. A keypad and safety pair is a modest add. Full access control with vehicle loops, an intercom, and phone-app entry climbs toward the top of the range. We quote each of these separately so you can see exactly what you’re paying for.
- Old gate removal. Tearing out and hauling a rusted or failing gate and footing is real labor. It’s usually $200 to $550 and worth budgeting for rather than discovering later.
One local note worth knowing: Upland’s dry, hot summers and the wind that funnels down from the foothills put steady stress on gate hardware and operators. We see more sun-baked control boards and dust-choked photo-eyes here than in cooler inland cities, which is why we spec operators and safety gear for the climate rather than the cheapest box on the shelf. Getting the install right the first time is the cheapest thing you can do.
How to Save on Gate Installation
There’s no reason to pay the top of the range for a job that doesn’t need it. A few practical moves keep Upland gate installation costs down:
- Keep your existing footing if it’s solid. A sound concrete pad that already meets code can save $600 to $1,800. We inspect it during the estimate and tell you honestly whether it’ll hold a new gate.
- Match the operator to your actual use. A household that opens the gate six times a day doesn’t need a commercial-duty DoorKing. Choosing the right tier for your traffic saves real money without sacrificing reliability.
- Bundle the access control at install. Adding a keypad or entry system during the installation is cheaper than retrofitting it a year later, because the wiring is already open.
- Repair before you replace when it makes sense. If your gate frame is sound and only the motor or control board has failed, a repair can cost a fraction of a new install. We’ll never push a replacement you don’t need.
- Get a written, itemized estimate. Upfront pricing means no surprises. Ours breaks out the gate, the operator, the footing, and the site work so you can compare apples to apples. Call (833) 918-6938 for a free estimate.
The best savings usually come from choosing a gate-only specialist in the first place. A generalist who mostly does garage doors treats your gate as a side job and often has to figure out your brand on-site. We already know the brands, which means fewer return trips, fewer wrong parts, and a job done right the first time. You can see the full scope of what we do on our Gate Installation in Upland page, and get oriented on our home page if you’re new to us.
FAQs – Gate Installation Cost
How much does a basic gate installation cost in Upland?
A basic manual single swing gate in Upland runs $2,400 to $4,200 installed. Add automation and the total typically climbs to $4,000 to $7,500 depending on the operator brand and whether new footing or conduit is needed. Call (833) 918-6938 for an exact quote on your driveway – estimates are free.
Is it cheaper to repair my existing gate or install a new one?
Repair is usually cheaper when the gate frame and posts are sound – often a fraction of a full install. New installation makes more sense when the frame is rusted through, the footing is failing, or you’re upgrading from manual to automated. We quote both so you can decide with real numbers, then call (833) 918-6938 to book the free estimate.
How much does an automatic gate operator add to the cost in Upland?
An automated operator adds $1,600 to $3,800 on top of the gate itself, depending on brand and duty level. Entry-level residential operators from Ghost Controls or Mighty Mule sit lower; professional-grade FAAC, BFT, and DoorKing systems sit higher. Call (833) 918-6938 and we’ll match an operator to your gate and daily use.
Do I need a permit to install a gate in Upland?
Automated driveway gates that cross a public approach or involve new electrical work typically require a permit, and Upland follows standard California requirements for gate safety devices. We’ll tell you during the estimate exactly what your project needs so nothing stalls the job. Call (833) 918-6938 with your address and we’ll walk you through it.
Can you install my gate and get it working the same day?
Many residential gate installations are completed in a single day, and straightforward replacements of an existing gate on a sound footing are the most common same-day jobs. Larger dual-swing or sliding projects with new conduit often take two days. Call (833) 918-6938 to schedule and we’ll give you a realistic timeline up front.
Why Choose a Gate-Only Specialist for Your Upland Install
Most companies quoting gate installation in Upland are garage-door shops that bolt on gates as an afterthought. A gate is a different system: different operators, different safety logic, different access hardware. We do gates and nothing else, which is why we’re fluent in the nine brands you’re most likely to own – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule – and why we can diagnose by brand instead of guessing. From the motor to the control board to the safety loops, every part of the system is work we do every day.
That focus pays off at install time and long after. When your gate needs service down the road, you’re calling the same specialists who put it in, not a company that has to re-learn your system. Repair or replace, we handle both, so you never need a second vendor when it’s time to upgrade.
Ready for a real number? We give free, itemized, upfront estimates for Gate Installation services across Upland and the surrounding area. Call (833) 918-6938 today, tell us your gate width and what you want it to do, and we’ll get you a written quote with no pressure and no vague “it depends.”
Pricing reflects the Upland market as of 2026. Falcon Gate Repair offers free estimates – call (833) 918-6938.
What Our Customers Say
"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
- Alicia Carter"The loop detector under the driveway had failed and residents were stuck holding the button. He traced it, found the break, and had the exit loop reading cars again the same visit."
- Adam Sullivan"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
- Ryan Doyle