Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for Upland Homeowners
A gate that won’t open, won’t close, or grinds halfway and stops isn’t something to put off. In Upland, where driveways slope up from the street and iron gates face daily sun exposure and occasional Santa Ana wind loads, a failed gate means a blocked car, a weakened security line, and a real headache. Falcon Gate Repair fixes gates for a living. We’re gate-only specialists, which means every call we take in Upland is about a gate, not a garage door, not a fence, not a side project. Our technicians arrive with factory-level familiarity across nine major operator brands, so the diagnosis usually starts before the van is parked. If your gate is down in Upland right now, call (833) 918-6938 and we’ll get you back in service today.
Driveway Gate Repair
Driveway Gate Repair covers the full range of failures that stop an automatic or manual driveway gate from operating correctly, from a dead motor and stripped gear to a sagging hinge that drags the gate leaf across the concrete. In Upland, most driveway gates we see are either sliding cantilever systems on the larger hillside properties north of the 210 or swing gates on the flatter lots near downtown. A typical driveway gate service call in Upland runs between $125 and $450 depending on whether we’re replacing a failed component or rebuilding a mechanical section, and you can learn more about Gate Repair pricing on our site. Falcon Gate Repair handles both the motor side and the steel side, so the fix doesn’t get split between two companies.
Motor and Operator Diagnosis
When a driveway gate stops responding, the operator is usually the first suspect but not always the culprit. We test the control board, capacitors, limit switches, and gear train before recommending any part replacement, because a Gate that trips its breaker and a Gate that has a dead motor produce similar symptoms with very different price tags.
Hinge, Track, and Level Corrections
Upland’s freeze-thaw cycle through winter and the dry summer heat both work against gate alignment over time. We reset gate posts, replace worn hinge bushings, and re-level tracks so the gate moves without binding, which also reduces the load on the operator and extends its life.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Gate Welding
Gate Welding is the repair method used when structural steel on a gate cracks, separates, or tears loose, usually at the hinge mounts, the operator attachment plate, or the mid-rail joints where vibration concentrates. We see this most often on heavier ornamental gates in Upland that have been running on undersized hinges for years. Welding repairs on a gate typically run between $180 and $600 in Upland, depending on the location of the crack, the thickness of the material, and whether the gate must be removed for proper access. Falcon Gate Repair welds on-site whenever the position allows, which keeps the gate in place and the driveway open during the repair.
Structural Crack Repair
A hairline crack at a hinge plate will tear open within weeks if the gate keeps cycling, so we grind out the fracture, weld the joint back to full penetration, and reinforce the area with a gusset where needed. This stops the failure at the source rather than patching over it.
Hinge and Bracket Reattachment
When a hinge barrel shears off a gate post or an operator bracket rips from the gate frame, the repair is a combination of welding and realignment. We reattach the hardware, check the gate’s swing geometry, and confirm the operator isn’t fighting a misaligned leaf afterward.
Commercial Gate Repair
Commercial Gate Repair covers automated gates on apartment complexes, business parks, storage facilities, and gated parking areas in and around Upland, where downtime carries more than inconvenience, it creates a security gap and an access bottleneck. These are higher-cycle systems that see thousands of open and close cycles per month, so the failure mode is usually a worn gear, a burned contactor, or a loop detector that has stopped reading vehicles. Commercial gate repair in Upland typically starts around $250 for diagnostics and runs upward of $800 when the repair involves replacing a heavy-duty operator head or rewiring an access control panel. Falcon Gate Repair is staffed for commercial work with the same gate-only focus we bring to residential calls, and we’re familiar with FAAC, BFT, and DoorKing commercial equipment, which covers most of the installed base in the Inland Empire.
Access Control Integration
When a commercial gate stops responding to a keypad, card reader, or telephone entry system, the fault can sit in the operator, the wiring, or the access device itself. We trace the circuit end to end and repair the actual point of failure, so you aren’t paying for a new operator when the problem was a corroded splice in the pedestal.
High-Cycle Operator Rebuilds
Operators on commercial gates in Upland run hard, especially on apartment and warehouse properties, and factory rebuild kits are usually the difference between another five years of service and a full operator replacement. We rebuild gearboxes, replace limit assemblies, and install fresh drive belts where the design calls for them.
Iron Gate Repair
Iron Gate Repair addresses failures common to welded steel and iron gates, including rust-through at the bottom rail, cracked uprights, and hinge posts that have worked loose inside their concrete footings. Upland’s older neighborhoods have a lot of custom iron gates from the 1980s and 1990s, and many of them are worth repairing rather than replacing. Typical iron gate repair in Upland runs between $150 and $500, with pricing driven by the amount of section repair and whether the gate needs to come off its posts for rewelding, as covered in The Complete Gate Repair Guide for Upland Homeowners. Falcon Gate Repair evaluates the entire gate before touching a single joint, because an iron gate that’s cracking in one place is usually stressed in three.
Section and Rail Replacement
When the bottom rail of an iron gate rusts through or an upright picket snaps at a weld, we cut out the failed section and weld in matching steel, then dress the repair so it disappears under a coat of paint. The goal is a gate that looks original, not patched.
Post Reset and Reinforcement
An iron gate that drags is usually hanging on a post that has shifted in its footing, and tightening the hinge doesn’t fix that. We expose the footing, reset the post plumb, and add concrete or a steel core as needed so the gate hangs true and swings free.
Sliding Gate Repair
Sliding Gate Repair focuses on the track, rollers, and drive systems of gates that slide sideways rather than swinging open, a style we see frequently on Upland properties where the driveway meets the street at a grade too steep for a swing gate to clear. The most common failures are worn roller bearings, a bent or debris-choked track, and a drive chain that has stretched past its tensioner’s range. In Upland, sliding gate service calls typically run from $150 to $550 depending on whether the repair involves replacing rollers, straightening a track segment, or rebuilding the drive coupling. Falcon Gate Repair works on sliding gate systems from Viking, BFT, and Linear, among others, and we stock replacement rollers and track hardware for common configurations.
Roller and Track Service
Sliding gates fail gradually, a worn roller loads the track unevenly, which then wears the next roller faster, and by the time the gate is grinding, the whole undercarriage needs attention. We replace roller assemblies, clean and lubricate the track, and adjust the guide rollers so the gate travels straight without shimmying.
Drive Chain and Rack Alignment
A chain-driven sliding gate that jerks on startup usually has a stretched chain or a rack with worn teeth, and both problems accelerate if ignored. We set proper chain tension, replace worn rack sections, and align the drive sprocket so the gate starts and stops smoothly under load.
Wrought Iron Gate Repair
Wrought Iron Gate Repair is the specialized cousin of general iron work, focused on ornamental gates with scrolls, finials, and decorative elements that require careful welding and finish matching to preserve the gate’s character. Upland has a substantial stock of wrought iron driveway gates and pedestrian gates, and many of them are original to the home. Wrought iron repair in Upland usually costs between $200 and $600, influenced by how intricate the broken section is and whether the repair requires hand-forging a replacement scroll or picket tip. Falcon Gate Repair has the welding capability and the patience to repair ornamental work without making it look repaired.
Ornamental Section Rebuilding
When a scroll snaps or a finial rusts away, we fabricate a replacement piece to match the original pattern rather than welding in a flat bar and calling it fixed. The repair is shaped, welded, and finished so the gate keeps its original silhouette.
Finish Prep and Corrosion Arrest
Wrought iron gates in Upland take a beating from summer UV and the occasional wet winter, and surface rust at weld joints is where most structural failures begin. We grind back the corrosion, treat the base metal, and prep the repaired area for primer and paint so the fix outlasts the original coating.
Metal Gate Repair
Metal Gate Repair is the broad category covering aluminum, steel, and iron gates of any construction, including tubular aluminum driveway gates, steel perimeter gates, and mixed-material pedestrian gates. The repair could be anything from welding a cracked steel frame to replacing bent aluminum pickets or rehanging a gate that has settled out of square. In Upland, general metal gate repair runs between $150 and $500 for most jobs, with the final number set by the damage type and the time required to correct alignment after the repair. Falcon Gate Repair is comfortable with all of it, because metal gates are what we work on every single day.
Tubular Aluminum Straightening
Aluminum gates bend before they break, and a gate that’s been bumped by a car or pushed by the wind will often have a bowed top rail that makes the whole gate look failed. We straighten or section-replace bent aluminum members and then set the gate back on its hinges with proper clearance.
Frame Repair and Reinforcement
Steel gate frames crack at the corner welds first, especially on heavy gates with single-point latches. We weld the cracked corners, add internal reinforcement where the design allows, and correct the racking so the gate doesn’t twist itself apart again.
Wood Gate Repair
Wood Gate Repair covers the structural and hardware problems common to wooden driveway gates and pedestrian gates, including sagging, rotted stiles, loose diagonal bracing, and hinge hardware that has torn out of the wood. Upland’s dry, hot summers shrink the wood, and the occasional wet winter swells it, a cycle that loosens fasteners and accelerates rot at ground contact. Wood gate repair in Upland typically runs from $120 to $400 for brace-and-hardware work, and higher when a rotted section of the gate frame needs to be cut out and replaced. Falcon Gate Repair handles wood gates with the same flat-rate discipline we apply to steel, no surcharges for being a gate-only shop.
Brace and Hardware Rebuilds
A wood gate sags when the diagonal brace loses its connection, and no amount of hinge tightening will fix a gate that’s pulling itself apart. We reset the brace with structural fasteners, replace the hinge hardware with heavy-duty plates, and true the gate so it latches like it did when it was new.
Rotted Frame Section Replacement
When the bottom of a wood gate stile has gone soft, we cut the rotted section out and sister in new lumber or replace the entire stile, then seal the end grain so water stops wicking up into the wood. The repair restores both the strength and the working life of the gate.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
Falcon Gate Repair is factory-familiar with FAAC, BFT, Linear, and Viking operators, among others, and that familiarity – detailed in our guide on Choosing the Right Gate Repair Brand: A Buyer’s Guide for Upland – changes how we work. When a FAAC 740 or 844 controller shows an error state, we read the code against the brand’s actual diagnostic logic rather than guessing at the symptom. When a BFT sliding gate loses its limit reference, we know the reset sequence and the common failure points on that line.
The same applies to Linear swing operators and Viking heavy-duty slide units. We’ve diagnosed enough of each to know which faults are common on which models, which parts interchange, and when a repair genuinely won’t hold and a replacement is the honest call. If your gate runs on a FAAC, BFT, Linear, Viking, or any other recognizable make, we can help you get it running again.
If you have a gate that needs repair in Upland, call Falcon Gate Repair at (833) 918-6938. Our Gate Repair in Upland service covers the entire city, and you’ll get a straight answer about what’s wrong before any work begins. For neighbors on the other side of the 10 freeway, we also handle Gate Repair in Ontario and Gate Repair in Rancho Cucamonga with the same gate-only focus.
Signs You Need a Pro Right Now
- Gate starts, then reverses or stops halfway. This usually means a safety sensor is misfiring, a limit switch has failed, or the gate is binding on its track. Continuing to run it against resistance burns out the motor and turns a $200 fix into an $800 replacement.
- Loud grinding or screeching during travel. Grinding is metal on metal, typically a failed roller bearing or a gear that’s running dry, and screeching is usually a hinge or track that needs immediate lubrication and alignment. Both failures destroy themselves faster the longer they run.
- Gate sags visibly, or scrapes the driveway. A sagging gate means the hinge posts or the frame itself have given up some structural integrity. The scraping you see is the gate destroying its own bottom rail, and the operator is working double to move the extra load.
- Keypad or remote works intermittently. Intermittent operation can be a failing receiver, a corroded wire connection, or a control board that’s on its way out. These problems never self-heal, and they have a habit of failing completely at the worst possible time, like when the gate is closed and the car is inside.
- Gate is stuck open or closed, manual release won’t work. When the manual release chain won’t let you move the gate by hand, there’s often a mechanical bind or a failed drive component involved. This is the point where the gate is genuinely down, and delaying the call just extends the downtime.
Our Process, Step by Step
- 1
Call and describe what the gate is doing. When you call (833) 918-6938, we’ll ask specific questions about your gate’s brand, type, and the exact symptom. That conversation often tells us which parts to load on the truck, which can mean a same-day fix instead of a second visit.
- 2
On-site diagnosis with the operator under test. We arrive and run the gate through its cycles while checking voltage, limit positions, and mechanical movement. For motorized gates, we test components in place using a multimeter and the manufacturer’s diagnostic sequence for the specific operator model.
- 3
Straightforward quote, approved before we start. We explain what failed, why it failed, and what the repair costs, all quoted and agreed before any work begins. You’ll know the number before we pick up a tool, and there are no surprise add-ons.
- 4
Repair with factory-level parts and procedures. We complete the repair using OEM parts where they matter and proven equivalents where they don’t, and we test the gate through multiple open and close cycles under real load. For welded repairs, we clean and prep the area and confirm alignment before we pack up.
- 5
Final walkthrough and adjustment. Before we leave, we show you what was replaced or repaired, explain any settings that changed, and make sure the gate operates smoothly from every control point. You get a clear rundown and a gate that works as it should.
How Much Does Gate Repair Cost in Upland?
A typical gate repair in Upland runs between $125 and $600 for most residential work. Simple fixes like a hinge adjustment, a limit switch replacement, or a remote reprogramming land at the lower end, between $125 and $225. Mid-tier jobs, including roller replacement, welding a cracked rail, or rebuilding a drive coupling, typically run $250 to $450. Full operator rebuilds, access control rewiring, or commercial-grade repairs can exceed $600, and we’ll tell you if a replacement makes better financial sense before you commit.
Three things drive most pricing: the type of failure, the accessibility of the gate, and whether replacement parts are needed. A gate with a fused disconnect and a gate with a stripped gear are entirely different jobs even if both “won’t open.” The best way to avoid overpaying is to hire a gate-only specialist who diagnoses by brand logic, we don’t sell you a new operator when the problem is a $40 sensor. Our free estimates include a full written quote, and the price you approve is the price you pay.
Our Service Area Near Upland
Falcon Gate Repair serves Upland and the surrounding Inland Empire communities, including Ontario, Rancho Cucamonga, Fontana, Pomona, Chino, Chino Hills, Montclair, Claremont, and Diamond Bar. Most Upland calls are reached the same day, and we keep our truck stock broad enough to handle common operator brands and mechanical hardware without a second trip. For more detail on the areas we cover, visit our home page or the location pages linked above.
Serving Upland, CA – Our Local Coverage Area
We’re based in the Upland area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Repair in Upland
Gate repair is the process of diagnosing and fixing failures on automatic and manual gates, including motors, control boards, hinges, tracks, rollers, and structural steel. At Falcon Gate Repair, we focus exclusively on gates, so the repair covers everything from the operator to the gate leaf itself. That includes mechanical work like welding and alignment and electrical work like circuit board and safety loop repair.
Most residential gate repairs in Upland are completed the same day, with simple mechanical fixes and common operator repairs taking one to three hours on site. Structural repairs that require welding or post resetting can take longer, and some commercial repairs span two visits if parts must be ordered. We’ll give you a realistic time expectation when we quote the job.
Gate repair in Upland typically costs between $125 and $600 for residential work, depending on the failure type and parts required. We quote every repair before work begins, so you’ll approve the exact number in advance. Call (833) 918-6938 for a free estimate on your specific gate.
Yes. We’re factory-familiar with FAAC and BFT operators and work on them regularly across Upland and the surrounding cities. Our technicians diagnose these systems by the brand’s actual operating logic, so we can isolate failures quickly and repair them without guesswork.
When a gate is stuck open or blocked closed, we prioritize those calls as urgent and work them into the same day whenever possible. Call (833) 918-6938 and tell us what the gate is doing, and we’ll give you a straight answer on timing and the soonest we can have a technician on site.
Repair work at Falcon Gate Repair is backed by our workmanship guarantee, and the parts we install carry their manufacturer’s warranty. We’ll tell you exactly what’s covered and for how long before we start the job, so there’s no ambiguity about what happens if something fails after we leave.
Clear the area around the gate so technicians have full access to the operator, hinges, and track, and make sure the gate’s power disconnect is accessible. If you have a vehicle inside the yard, know that we may need to open the gate manually during diagnosis, so leave enough room for us to work the gate through its full travel.
Schedule Your Gate Repair Service in Upland Today
A gate that won’t work isn’t a problem that improves with time, and every cycle on a failing operator makes the repair more expensive. If your gate is down in Upland, call Falcon Gate Repair at (833) 918-6938 for a free, no-obligation estimate. We’ll diagnose the problem honestly, quote the price before any work starts, and get your gate back in service today.
Written by Allen Prescott, Owner at Falcon Gate Repair, serving Upland and the surrounding Inland Empire.